Finishing Ideas for Handcrafts

Floss Wallet

September 20, 2009
2 Comments

I’ve been working on this idea for a while.  I love the little zip-loc bags to keep my floss in, and I normally use a ring to keep all the little baggies for a project together.  But what’s the use of being a cross-stitcher if you can’t make a little useful item, right?

TIP: When combining cross stitch and fabric – pick your fabric first – then choose your floss.  It’s much easier to find the right floss colors to use with a fabric – not so easy to find fabric to match an existing cross stitched project.

The chart I used for this project is Petit Abécédaire aux Fleurs.

1. Cut two pieces of fabric 7 x 11 inches for the inside and outside of the Floss Wallet.  9-2009 192
2. Cut one piece of fabric 7 x 6 inches (for frame lining).
3. Cut two pieces of fabric 4 x 7 inches for two pockets.  Fold under a ½ inch hem on each pocket, apply lace trim to the right side, if desired. 9-2009 193
4. Top stitch the lace in place, catching the hem as you go. 9-2009 194
5. Pin the pockets to either end of the lining (inside) fabric, right sides up.  If you want to make a divided pocket, fold the lining in half lengthwise and mark the center. 9-2009 195
6. Top stitch the center line (the pencil is pointing to the top stitching). 9-2009 196
7.  Find the center of the 7 x 6 inch piece of fabric and mark it on the wrong side.  9-2009 197
8. Measure the cross stitched piece to determine the size opening you need. 9-2009 198
9. Mark the opening size on the wrong side of the 7 x 6 inch piece of fabric, centering on your mark.  I wanted to have curved corners, so I used the handle of my rotary cutter to mark curves at each corner.  9-2009 199
10. Lay the 7 x 6 inch fabric, right sides together, on one end of the 7 x 11 outside piece, matching the corners.  Pin securely (I believe in using straight pins – they give you 300 hundred in that little box for a reason, right?).  9-2009 200
11. Stitch on the marked line.  Cut out the center, leaving about ¼ inch seam allowance, and clip the inside curves nearly to the stitching.  9-2009 201
12. Turn the lining thru the center to the wrong side.  Press the seam flat.  Lay the opening over your stitched piece and center it in the opening.  9-2009 202
13. Trim the stitched fabric to match your fabric and pin around the edges thru all three layers.  9-2009 203
14. Forgot about cutting a tab – cut a scrap of fabric about 6 x 1-1/2 inches – fold in half lengthwise and stitch the long sides.  9-2009 204
15. I again used the handle of my rotary cutter to mark a curve on the folded end of the tab and stitched along that curved line.  Trim the seam and clip the curve.  9-2009 205Turn the tab right side out.
16. Lay the front piece down right side up.  Lay the lining piece on top of it right side down.  Put the tab in between the two pieces at the center of the short end, matching the raw edges.   Sew a ½ inch seam along the two long ends and across the short end where the tab is.  Trim the seam and clip the corners (sorry, the photos of these steps didn’t come out – I didn’t realize my camera batteies were nearly dead.)
17. Cut two pieces of iron on quilt batting 5-¾ inches by 10 inches.  Cut out four holes 1 inch in from the sides and about ½ inch from the center (to allow for grommets) .  Iron the batting to each of the wrong sides.  9-2009 206
18. Be sure to use a pressing cloth to iron the batting in place.  This is what happens if you get impatient and don’t use a cloth. 9-2009 207
19. Turn the wallet right side out.  Mark the positions of the four grommets. Don’t apply the grommets yet! 9-2009 208
20. Cut two pieces of thin cardboard, each 6 inches by 4-1/4 inches.9-2009 209
21. Slide one piece of cardboard inside the wallet between front and back batting, all the way to the end.  Apply the four grommets.  9-2009 210And yes, that’s a Crop-o-dile peeking in from the edge of the photo!
22. Slide the second piece of cardboard inside the wallet and push down to the grommets. 9-2009 211

23. You may have noticed that I had applied a snap closure.  Unfortunately, after I applied it, I tried it out, and it wouldn’t snap!  So I had to pry off the snap, and sew on a button instead.  9-2009 212I made a matching button hole in the tab.
Fold under the raw edges on the open end 1/4 inch, and whipstitch it closed.  I used matching floss.  (You can barely see the pins holding the opening closed in the above photo).

24. Here’s the inside of the wallet, with a packet of needles in one pocket and my scissors in the other.  9-2009 213
25. And the inside with some floss baggies on the rings (which went thru the grommets).  These are the flosses I’m using for a current project (shh – it’s a secret!) 9-2009 214
26. The back of the outside, showing the tab buttoned.  9-2009 215
27. And the front.  9-2009 216
28. Here it is standing up, so you can see some of my mess scattered around the table – lol!  9-2009 218

And here is the chart I’m planning to use for my next wallet.  BAPIf you’d like to use this chart, feel free to take a copy for your personal use – and please send me a photo of your project!

Your comments, questions and suggestions are welcome.

Thanks for visiting today!

Advertisements